A1 Cardone 77-6106F Engine Control Module in Canada

Buyer fitment guide only intended as reference. Please use catalogue search by vehicle to ensure proper fitment.

Chevrolet 12570558
Chevrolet 12576106
GMC 12576106

CARDONE Remanufactured Electronic and Powertrain Control Modules are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. All critical components are re-soldered or replaced at our Philadelphia manufacturing plant, and each unit is 100% computer tested to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance.
As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%.
On-car vehicle validation is done to test durability and performance.
Re-soldering of critical components ensures superior electrical connections. This prevents intermittent failures and leads to longer product life.
Tested with automated computer equipment or bench-tested, depending on application, to ensure functionality.

Other Names: Engine Control Module, Engine Control Module, Powertrain Control Module

Connector Gender	Female
Connector Quantity	2
Contains Electronic Components?	Circuit Board
E-Waste	Yes
FAA_A1	â€œECMâ€ stands for Electronic Control Module. â€œPCMâ€ stands for Powertrain Control Module. Both the ECM and PCM control the engine; however, the PCM also has control over the transmission.
FAA_A2	Some GM applications have a knock module that must be transferred to the replacement module. Some older Ford applications have a calibration module that must be transferred to the replacement module.
FAA_A3	No, not all Ford vehicles require PATS reset. Check the PATS chart found on the O.E. Manufacturerâ€™s Service site for your application.
FAA_A4	Ensure that the PCM was properly flash programmed for the vehicle. Also note whether the vehicle is equipped with the Ford "passive anti-theft system", which requires an on-car relearn.
FAA_A5	Prior to replacing the original ECM/PCM, the installer should determine what caused the original to fail. Common causes of failures are: poor grounds and power, a bad wiring harness and short-circuited solenoids/relays.
FAA_A6	Yes, most GM vehicles have a VATS, Pass Key or Pass Lock anti-theft system.
FAA_A7	Not necessarily. There is a 30-minute manual procedure that can be done without a scanner. Refer to your O.E. manufacturerâ€™s approved service manual for details.
FAA_A8	Chrysler models 1996 and newer will need to be VIN programmed.
FAA_A9	Check Engine Light staying on after resetting, engine turning off for no reason, loss of spark, loss of fuel injection, loss of pulse on fuel pump, intermittent starting problems.
FAQ_Q1	Whatâ€™s the difference between an ECM and a PCM?
FAQ_Q2	Do I have to transfer anything from my original ECM/PCM?
FAQ_Q3	Do all Ford vehicles require a Passive Anti-Theft System (P.A.T.S) reset?
FAQ_Q4	The replacement PCM for a Ford vehicle wonâ€™t start the vehicle. Why?
FAQ_Q5	What steps should I take to ensure the original PCM is causing the issue?
FAQ_Q6	Do GM vehicles have a passive anti-theft system?
FAQ_Q7	Do I need a scanner to reset the anti-theft system
FAQ_Q8	Do all Chrysler Power Train Control Modules (PCM) need VIN programming?
FAQ_Q9	What are the most common symptoms of a bad PCM?
Height	2.9
Height	73.66
Is item a chemical?	No
Is or contains a battery?	No
Is or contains a bulb?	No
Is the item CARB affected?	No
Length	182.88
Length	7.2
Package Contents	Module; Instruction Sheet
Product Condition	Remanufactured
Prop 65	No
SDS Required	No
Terminal Quantity	160
Terminal Type	Pin
Width	226.06
Width	8.9
UPC	082617707312
Origin Country:	MX
Weight:	3.79Lb. (1.72 kg.)
Package Dimensions:	9.8" x 7.4" x 3.3" (24.8 cm x 18.7 cm x 8.3 cm)

1 Year Warranty

A1 Cardone 77-6106F Engine Control Module

Remanufactured Powertrain Control Module