A1 Cardone 18-4851HD Disc Brake Caliper in Canada

Buyer fitment guide only intended as reference. Please use catalogue search by vehicle to ensure proper fitment.

NAPA Chassis Parts 2693671
MAS Industries TO50071
Ingalls Engineering IES800218
Beck/Arnley 1015752
OEM Part Number 53540SEPA02
Deeza ACT654
MOOG Chassis Products ES800217
TRW Steering and Suspension Parts JTE367
Transbec TES800217
Ingalls Engineering IES800217
Beck/Arnley 1015751
AutoZone ES800217
Beck/Arnley 1015751
Beck/Arnley 1015752
Ford 3W1Z2552CA
Ford 7W1Z2552B
Mercury 3W1Z2552CA
Mercury 6W1Z2552AA
Mercury 7W1Z2552B
Ford 3W1Z2552AA
Ford 6W1Z2552AA
Lincoln 3W1Z2552AA
Lincoln 3W1Z2552CA
Lincoln 6W1Z2552AA
Lincoln 7W1Z2552B

As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
Mounting bracket is included where applicable for a hassle-free installation.
New banjo bolts are included where applicable to ensure a perfect fit and quick installation.
New bleeder screws provide trouble-free bleeding and a positive seal.
New stainless steel hardware clips and new mounting pins are included where applicable.
New washers are included where applicable for a proper seal.
Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%.
Pistons are durable, resistant to cracking or pitting and handle great loads.
Rubber seals are replaced with new high temperature EPDM rubber for extended life and optimum performance.
A plastic cap plug protects every brake port thread to ensure trouble-free installation.
Brand-new steel piston and a high-grade seal ensure the ultimate performance under excessive heat and wear.
Calipers are treated with a special formulated rust inhibitor and kept in the original equipment finish.
Developed to operate at high performance levels under extreme conditions of heat and wear, CARDONE Severe-Duty Calipers are expertly remanufactured to rigorous quality and performance standards. These calipers are equipped with brand-new, premium components to guarantee exceptional longevity and reliability and 100% pressure-tested to deliver consistent braking performance. Each unit arrives with a complete set of brand-new hardware for a simple, complete installation. Caliper bracket is included when applicable.

Bleeder Screw Cap Included	No
Rust Resistant Coating	Yes
Dust Boots Included	Yes
Bleeder Thread Size	M10x1.0
Inlet Port Size	9.52125
Inlet Port Size	0.375
Product Condition	Remanufactured
Package Contents	Caliper; Instruction Sheet; Hardware Kit
Prop 65	No
E-Waste	No
SDS Required	No
Contains Electronic Components?	No
Is item a chemical?	No
Is or contains a battery?	No
Is or contains a bulb?	No
Is the item CARB affected?	No
FAQ_Q1	Can I switch out a Phenolic Piston Caliper for a Steel Piston Caliper or vice versa?
FAA_A1	Not recommended. The O.E. manufacturers specified steel or phenolic pistons based on the intended use of the vehicle. It is recommended that the installer follow the manufacturerâ€™s recommendations.
FAQ_Q2	What type of fluid should I use: DOT 3, DOT 4, or DOT 5?
FAA_A2	As a rule, always use brake fluid recommended by O.E. The fluid type is stamped on the master cylinder reservoir lid. Always use new fluid in a sealed container.
FAQ_Q3	Car pulls to one side during braking. Why?
FAA_A3	Inspect both calipers for binding or sticky slides or pins. Also ensure that brake hoses are not collapsed or restricted and inspect steering/suspension components for proper operation.
FAQ_Q4	Brakes squeal all of the time. What's causing the squeal?
FAA_A4	Brake squeal can be caused by improper installation of the brake pads, improperly installed brake hardware and improper brake rotor finish.
FAQ_Q5	Could calipers be the cause of a low brake pedal?
FAA_A5	A symptom of a low brake pedal is usually caused by air in the system, misadjusted rear brake shoes, deteriorated brake hose(s) or a defective master cylinder.
FAQ_Q6	What type of grease is used on floating caliper mounting pins?
FAA_A6	A silicone grease is used on floating caliper mounting pins.
FAQ_Q7	Do all of your Calipers come with the new hardware and a mounting bracket for installation?
FAA_A7	New hardware is included with all of our Calipers however the mounting bracket is an added option depending on part number and application. Mounting Brackets are also sold separately for most applications.
UPC	884548117877
Origin Country:	US
Weight:	6.5Lb. (2.96 kg.)
Package Dimensions:	8" x 6.1" x 5.3" (20.3 cm x 15.6 cm x 13.3 cm)

1 Year Warranty

A1 Cardone 18-4851HD Disc Brake Caliper

Remanufactured Unloaded Caliper